Buckeye 1-1/4" Mechanical Gas Valve - BFGV-125
Are you a fire protection company? Get wholesale pricing
Wholesale PricingRelated Documents
The Buckeye 1-1/4" Mechanical Gas Valve (BFGV-125) is a mission-critical component for the Buckeye BFR series fire suppression system. While larger 1-1/2" or 2" valves are reserved for primary headers, the BFGV-125 is the definitive choice for secondary gas manifold safety. This 1-1/4" NPT mechanical gas valve performs the vital task of mechanical fuel termination, acting as a normally open (NO) device that automatically closes the fuel supply to cooking batteries the moment the system actuates.
Operating on an immutable tension-release actuation logic, the valve remains open only while the 1/16" stainless steel cable is under tension. Upon a thermal or manual trigger, a heavy-duty internal spring initiates a spring-loaded kinetic closure, snapping the valve shut in milliseconds. This power-independent fuel isolation ensures your facility meets UL 300 compliance standards even during total electrical failure. The valve requires a local manual reset, ensuring a professional inspection occurs before gas flow is reintroduced to the system.
| Feature | Details |
|---|---|
| Manufacturer | Buckeye Fire Equipment |
| Part Number | BFGV-125 |
| Pipe Size | 1-1/4" NPT Threads |
| Actuation Type | Mechanical (Cable / Tension-Release) |
| Operating Mode | Normally Open (NO) / Spring-Loaded Close |
| Body Material | Heavy-Duty Cast Metal |
| Reset Requirement | Local Manual Reset (Technician Required) |
| System Compatibility | Buckeye Kitchen Mister (BFR Series) |
| Certifications | UL Listed, ULC Listed, FM Approved |
The BFGV-125 must be installed by a licensed fire suppression technician and licensed gas fitter in accordance with the Buckeye Kitchen Mister BFR system design manual, NFPA 17A, and NFPA 96. The valve must be installed in accordance with the flow direction arrow on the body. Improper alignment can lead to galling or a partial seal, which would violate NFPA 17A requirements for a total fuel shut-off. The pipe must be properly supported with hangers on both sides of the valve to prevent mechanical stress on the valve body.
Every six months, a certified technician must trip the fire system to verify that the BFGV-125 snaps fully shut. Visual cable tension inspection alone is not sufficient; the technician must confirm 100% gas flow obstruction to satisfy NFPA 17A requirements. The entire 1/16" stainless steel cable run must also be inspected for wear, fraying, or binding through corner pulleys. Following actuation, the valve requires a local manual reset at the installation point; it cannot be reset from the pull station. This local reset protocol ensures a qualified professional has cleared the hazard zone and verified the suppression system is back in a ready state before fuel is reintroduced.
When should I specify a 1-1/4" valve over a 1-1/2" model?
The choice is determined by the total BTU load of your secondary branch line. The BFGV-125 is sized for facilities where a 1-1/4" diameter is required to feed medium-to-large culinary batteries without inducing a significant pressure drop. Always consult your system's as-built drawings to match the valve size to the manifold diameter.
Does this valve require a specific mounting orientation?
Yes. To ensure the internal gate seats properly during a mechanical fuel termination event, the valve must be installed in accordance with the flow direction arrow on the body. Improper alignment can lead to galling or a partial seal, which would violate NFPA 17A requirements for a total fuel shut-off.
Can the BFGV-125 be reset from the pull station?
No. This valve utilizes a local manual reset protocol, meaning a technician must physically reset the valve at the installation point under the hood. This acts as a safety buffer, preventing fuel from being turned back on until the hazard zone has been cleared and the suppression system is back in a ready state.
