Amerex KP 600 Mounting Bracket - 23184
The Amerex 23184 is a mission-critical mounting bracket for the KP 600 cylinder, the largest unit in the Amerex wet chemical family. Designed to protect sprawling appliance batteries and large-scale exhaust hoods, the KP 600 demands more than a standard J-hook or light-duty bracket can provide. The 23184 utilizes a precision-formed steel backplate and a dedicated 15412-P001 stainless steel belly strap to ensure the tank stays vertical and immovable throughout its service life.
In a commercial kitchen, extreme thermal cycling and aerosolized grease create conditions that quickly degrade non-OEM hardware. A bracket that fails to maintain structural integrity can allow the cylinder to tilt, stressing the copper or stainless steel discharge piping and leading to leaks. The genuine 23184 mounting kit ensures fire system structural integrity from the wall to the nozzle, and is fully compliant with UL 300 mounting and NFPA 17A bracket requirements.
Static Load Engineering
A fully charged Amerex KP 600 cylinder weighs approximately 114 lbs (51.7 kg), exerting over 500 Newtons of constant downward force on the bracket. The 23184 backplate is manufactured from thick formed steel specifically designed to resist bending moments and distribute this load evenly across the mounting surface.
Vibration and Discharge Surge Protection
During system actuation, the rapid release of nitrogen into the wet chemical agent creates an internal pressure surge. Without the stainless steel belly strap (P/N 15412-P001), this surge could cause the cylinder to jump or oscillate. The 23184 locks the cylinder into a three-point contact state, neutralizing kinetic movement and protecting the threaded pipe connections at the valve body.
Corrosion-Resistant Finish
The bracket is finished with a heavy-duty black paint formulated to resist high-alkaline degreasers and steam. This prevents oxidative scaling that can weaken non-OEM brackets over a 10-year service life, maintaining reliable cylinder support for the long term.
| Feature | Details |
|---|---|
| Manufacturer | Amerex Corporation |
| Part Number | 23184 |
| Compatible Cylinder | Amerex KP 600 (Model 600) |
| Tank Diameter | 12-inch cylinder mount (30.5 cm) |
| Base Material | Heavy-duty formed steel |
| Strap Material | Stainless steel belly strap (P/N 15412-P001) |
| Mounting Style | Vertical wall mount |
| Hole Pattern | 3-hole vertical alignment |
| Gross Weight Support | Rated for approximately 114 lbs (full capacity) |
| Compliance | UL Listed, UL 300 Mounting |
Fastener Selection by Substrate
The 23184 does not include mounting screws, as fasteners must be matched to the wall substrate. Amerex recommends the following:
- Wood studs: Heavy-duty lag bolts with at least 2.5 inches of penetration.
- Cinder block / masonry: Expansion anchors or Tapcon-style masonry screws.
- Metal studs: Through-bolts with backing plates to prevent the bracket from tearing through thin-gauge metal.
The Vertical Alignment Mandate
All three pre-drilled holes must be utilized during installation. Using fewer than three mounting points allows the bracket to pivot under the immense weight of the cylinder and agent, creating a compliance violation and a structural hazard.
Maintenance Accessibility
The 15412-P001 belly strap is designed for rapid release. During a 12-year hydrostatic test, the cylinder can be unstrapped and lifted without unscrewing the base from the wall, significantly reducing labor time and facility downtime.
Semi-Annual Inspection Points
During every 6-month inspection, technicians should check the belly strap for slack. A loose strap allows the cylinder to vibrate against the wall, leading to premature wear of the protective coating and eventual rust on the bracket body.
Can this bracket be used for the smaller KP 275 or KP 375 cylinders?
No. The 23184 is sized specifically for the 12-inch cylinder mount of the Model 600 tank. The KP 275 and KP 375 use the universal 16920 bracket. Using the 23184 for a smaller cylinder will result in a loose fit, which is a major compliance violation as it cannot guarantee the cylinder stays connected to the discharge piping.
Does the bracket come with the belly strap?
Yes. The 23184 mounting kit is a complete assembly that includes both the formed steel backplate and the 15412-P001 stainless steel strap. Wall mounting hardware is sold separately and must be selected based on the substrate.
Can I mount the KP 600 horizontally if space is tight?
No. The KP 600 is a stored-pressure unit that relies on an internal siphon tube. Horizontal mounting will result in a partial discharge, as pressure will escape before all wet chemical agent is forced out. The 23184 is strictly a vertical-mount bracket.
Best Sellers
